Search results for " Photovoltaic modules"
showing 9 items of 9 documents
A procedure to calculate the I–V characteristics of thin-film photovoltaic modules using an explicit rational form
2015
Abstract Accurate models of the electrical behaviour of photovoltaic modules are effective tools for system design. One or two diode equivalent circuits have been widely used even though some mathematical difficulties were found dealing with implicit equations. In this paper, a new model based on a simple rational function, which does not contain any implicit exponential form, is presented. The model was conceived in order to be used with thin-film photovoltaic modules, whose current–voltage curves are characterised by very smooth shapes. The parameters of the model are evaluated by means of the derivatives of the issued characteristics in the short circuit and open circuit points at standa…
An accurate one-diode model suited to represent the current-voltage characteristics of crystalline and thin-film photovoltaic modules
2020
Abstract In this paper a new one-diode model, conceived in order to be used to represent the current-voltage curves of both crystalline and thin-film photovoltaic modules, is presented. The model parameters are calculated from the information contained in the datasheets issued by manufactures by means of simple iterative procedures that do not require the assumption of simplifying hypotheses. Some innovative relations describing the dependence of the parameters from the solar irradiance and cell temperature are adopted in order to permit the model to reliably simulate the electrical behaviour of photovoltaic devices operating in real conditions. The ability of the model to calculate the cur…
On the Efficacy of PCM to Shave Peak Temperature of Crystalline Photovoltaic Panels: An FDM Model and Field Validation
2013
The exploitation of renewable energy sources and specifically photovoltaic (PV) devices have been showing significant growth; however, for a more effective development of this technology it is essential to have higher energy conversion performances. PV producers often declare a higher efficiency respect to real conditions and this deviation is mainly due to the difference between nominal and real temperature conditions of the PV. In order to improve the solar cell energy conversion efficiency many authors have proposed a methodology to keep the temperature of a PV system lower: a modified crystalline PV system built with a normal PV panel coupled with a Phase Change Material (PCM) heat stor…
Optimization of photovoltaic energy production through an efficient switching matrix
2013
This work presents a preliminary study on the implementation of a new system for power output maximization of photovoltaic generators under non-homogeneous conditions. The study evaluates the performance of an efficient switching matrix and the relevant automatic reconfiguration control algorithms. The switching matrix is installed between the PV generator and the inverter, allowing a large number of possible module configurations. PV generator, switching matrix and the intelligent controller have been simulated in Simulink. The proposed reconfiguration system improved the energy extracted by the PV generator under non-uniform solar irradiation conditions. Short calculation times of the pro…
Assessment of the Usability and Accuracy of Two-Diode Models for Photovoltaic Modules
2017
Many diode-based equivalent circuits for simulating the electrical behaviour of photovoltaic (PV) cells and panels are reported in the scientific literature. Two-diode equivalent circuits, which require more complex procedures to calculate the seven model parameters, are less numerous. The model parameters are generally calculated using the data extracted from the datasheets issued by the PV panel manufactures and adopting simplifying hypotheses and numerical solving techniques. A criterion for rating both the usability and accuracy of two-diode models is proposed in this paper with the aim of supporting researchers and designers, working in the area of PV systems, to select and use a model…
Dynamic programming and Munkres algorithm for optimal photovoltaic arrays reconfiguration
2015
Abstract In this paper, an original formulation of the control problem for optimal PV array reconfiguration, following a Total Cross Tied layout, is proposed. The formulation follows the well-known subset sum problem, which is a special case of the knapsack problem. The reconfiguration is a measure devoted to mitigate the mismatch effect and maximize the output power of small photovoltaic plants under non-homogeneous working conditions. Therefore, reconfiguration means changing the connections of the solar panels adaptively by a dynamic switching matrix. The control system implements an easy dynamic programming algorithm to change the switches layout. The use of the Munkres assignment metho…
A novel approach for parameters determination in four lumped PV parametric model with operative range evaluations
2013
The paper presents a novel numerical approach for the parameters determination of crystalline silicon PV models four lumped parameters equivalent circuit. The novel approach basically deals with a new method, alternative to the iterative one known in literature, to calculate the series resistance. Particularly, it allows the evaluation of the lumped parameters on the basis of the manufacturer’s datasheet. The new approach has been validated both in the Maximum Power Point (MPP) and close to it by comparing values and curves obtained by means of the model implementation in Matlab/Simulink environment with those related to some five parameters models and manufacturer curves. Results show that…
A Dynamic Electrical Scheme for the optimal reconfiguration of PV modules under non-homogeneous solar irradiation
2012
This paper presents a strategy for the maximization of the output power of photovoltaic (PV) systems under non homogeneous solar irradiation by means of automatic reconfiguration of the PV arrays layout. The innovation of the proposed approach is the employment of a simple Dynamic Electrical Scheme (DES), allowing a large number of possible modules interconnection, to be installed between the PV generator and the inverter. The models of the PV generator and of the DES have been realized and simulated with Simulink (Dynamic System Simulation for MATLAB). The attained experimental results appear to be quite interesting in terms of the attainable benefit in power and thus energy terms. The lim…
Thin Film CIGS Solar Cells, Photovoltaic Modules, and the Problems of Modeling
2013
Starting from the results regarding a nonvacuum technique to fabricate CIGS thin films for solar cells by means of single-step electrodeposition, we focus on the methodological problems of modeling at cell structure and photovoltaic module levels. As a matter of fact, electrodeposition is known as a practical alternative to costly vacuum-based technologies for semiconductor processing in the photovoltaic device sector, but it can lead to quite different structural and electrical properties. For this reason, a greater effort is required to ensure that the perspectives of the electrical engineer and the material scientist are given an opportunity for a closer comparison and a common language.…